How to Make a Multistrand Bracelet

There’s a huge trend right now to wear lots of bracelets stacked on one arm.  This week’s tutorial is how to make one bracelet that looks like you are wearing a 12! I used a magnetic slide lock clasp which has six loops on either side to make this bracelet. I also used small sparkly bicones and faceted beads so that it would catch the light.  

This project takes quite a while to make as you have to string a lot of beads. It’s a good one to do while binging that Netlfix show.

Materials

My bracelet measured 18.5cm finished.  I have quite a small wrist so if you need a larger bracelet just add more beads.  I’ve given you the approximate number of beads I used below.  As beads tend to differ a little in size, it may be worth purchasing a few extras.

Tools

Instructions

Watch the video or read the instructions below.

Step 1 – Thread on the Beads

As I said, this is a good project to do whilst sitting in front of the television as this takes quite a while.

Cut 12 pieces of Tiger Tail approximately 35-40cm long depending on your wrist size.  You want to ensure you have lots of extra to work with.

Place one of your random beads onto a piece of Tiger Tail and then thread back up from the bottom to create a bead stopper.  This should be near one end.

 

Thread on enough beads to fit your wrist, then put another bead stopper on the end.

Repeat this until you have all your beads strung.  I created:

  • 4mm White AB Vacuum Beads x 2 strands
  • 3mm Blue Crystal Glass Bicones x 2 strands
  • 6mm Crystal Glass Faceted Beads x 1 strand
  • 4mm Pink Crystal Glass Faceted Round Beads x 2 strands
  • 4mm Aqua Crystal Glass Faceted Round Beads x 2 strands
  • 6mm Acrylic Bead Mix x 1 strand
  • 8x6mm White Cats Eye Beads x 1 strand
  • 4mm Lilac Crystal Glass Faceted Round Beads x 1 strand

Lay the strands out in the order you are going to attach them.  Above is the order I used.

I arranged my strands with the acrylic bead mix strand as strand 6, then I made sure that the other two larger bead strands were balanced roughly on either side.  

Attach the Strands to the Clasp

Take the top strand (3mm blue bicone in my case) and remove the bead stopper.  

To ensure the correct size, you’ll need to measure your strand and remove any excess beads or add more if needed. You want it to be your wrist measurement less 1cm (width of the clasp) plus 0.5cm (wiggle room). My wrist measures 18cm so I wanted my strands to be 17.5cm.

Put on a crimp bead, then thread the Tiger Tail through the end loop on one side of the clasp. Now thread the Tiger Tail back down through the crimp bead.  Ensure that the two strands of Tiger Tail are sitting parallel inside the crimp bead. Squeeze the crimp bead using your chain nose pliers so that it’s flat.

Trim the end of the Tiger Tail so that it will go through 2-3 beads.  Push the beads up close to the crimp and repeat for the other end, ensuring you attach this to the correct loop.

Repeat the process above attaching two strands to each of the loops.

That’s all you need to do to make this impressive multi-strand bracelet. It’s not hard to make but it does take quite a while.  If you’re new to jewellery making, I suggest that you watch the video in its entirety as there are quite a few tips as you go through.

I hope you enjoyed this tutorial.

If so...

PIN FOR INSPIRATION AND SHARE WITH YOUR FRIENDS!!

⇓ PIN THIS

If you like my blog be sure to click on the RECOMMENDED button and SHARE it with your friends! It’s the best way for my blog to grow. I would love for you to be part of my family so sign up to receive my emails. Every time I post a blog, I will send you an update email.Also, follow me on Facebook HERE,  Instagram HERE and Pinterest HERE.

Come by and say Hey!

August 24, 2021